Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2 User Manual
Browse online or download User Manual for For the car Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2. Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) User Manual
- Page / 1
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite
-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector
(“+” & “–” are marked on the side of connector)
. Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.
If needed,
add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
1
Summary of Contents
Page 1
NOVAK POWER CONNECTORSLow-Loss • Polarized • Gold-PlatedFor best results, strip, twist, & pre-tin about 1/4” of your 16-12G power wires before sol
Related products and manuals for For the car Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2
(1 pages)© 2020, manymanuals.com. All rights reserved. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals