Novak Brushless Motor: Drift Spec Motor (55-3074M-1 Rev. User Manual
Browse online or download User Manual for For the car Novak Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.. Novak Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.1) User Manual [en] [es] [de]
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
#55-3074M-1 Rev.1
6-2014
PRECAUTIONS
PRECAUTIONS
NEVER FREE-REV THE MOTOR Free-running your brushless
motor in a no-load condition can result in rotor failure and ESC
transistor damage & will void the product’s warranty!
• WATER & ELECTRONICS DON’T MIX Never allow water, moisture, or
other foreign materials to get inside motor, or on PCBs.
• NOVAK MOTORS & ESCs FOR BEST RESULTS Use Novak sensored
motors with Novak Brushless ESCs for best performance & protection. Only
use motors with the proper number of turns to match ESC’s rating.
• DO NOT USE WITH ESCS THAT HAVE ADVANCE ELECTRONIC
TIMING This can result in excessive heating and motor damage that will
not be covered by the product’s warranty.
• INSULATE EXPOSED WIRES Use heat shrink tubing to prevent shorts.
• NO SOLVENTS Do NOT expose the motor to any type of solvents.
• SET GEAR MESH PROPERLY Too tight of a gear mesh can result in
motor pinion shaft breakage--be sure to adjust mesh properly.
MOTOR MAINTENANCE
• CHECK ALL MOTOR SCREWS for loosening at regular intervals, just like
other hardware on your vehicle. Note: The 3 main socket head screws
that hold the motor together may require tightening after a few runs of
the motor. Also check the 3 flat head screws securing the end cap on
the back of the motor.
• CHECK MOTOR BEARING WEAR after extensive use. The motor’s
closed design will keep most dirt & debris out, but some will get in
and eventually cause wear. If the shaft does not spin freely, you may
need bearing replacement. A small drop of Novak Speed Lube (#5860)
on the bearings periodically can help extend bearing life--however, too
much oil will attract dirt and will cause problems, so apply sparingly.
• CLEAN INSIDE MOTOR periodically by removing front end bell,
removing the rotor, and blowing out the inside of the motor with
compressed air.
Be sure not to lose any small shim washers that may be
on the ends of the rotor shaft & keep them in the correct location.
SERVICE PROCEDURES
After reviewing instructions, tech section and how-to video section of website, if you feel
your motor requires service
(motor may appear to have failed when other problems exist)
, obtain
the most current product service options & pricing by one of the following methods:
WEBSITE:
Print a copy of the product SERVICE FORM from the SERVICE section of the
Novak website. Fill out the needed information & return it with the Novak product.
PHONE/E-MAIL: Contact our customer service department by phone or e-mail, and
we will supply you with current service options.
WARRANTY SERVICE:
You MUST CLAIM WARRANTY on product SERVICE FORM & include
a valid, itemized receipt with the purchase date on it, or an invoice from previous service
work. If warranty provisions have been voided, there will be a service fee.
ADDITIONAL NOTES:
•
Dealers/distributors are not authorized to replace products thought to be defective.
•
If a hobby dealer returns your product for service, submit a completed product SERVICE
FORM to dealer & make sure it’s included with items.
PRODUCT WARRANTY
Novak Brushless motors are guaranteed to be free from defects in materials or workmanship for a period of 120
days from the original date of purchase (verified by dated, itemized sales receipt). Warranty does not cover incor-
rect installation, components worn by use, cross-connection of battery/motor power wires, overheating solder
tabs, damage resulting from thermal overload or operation above 175°F, use of excessive timing or overheating,
splices or damage to the sensor harness, damage from disassembling motor, tampering with internal electronics,
allowing water, moisture, or any other foreign material to enter motor or get onto the PC board, short-circuiting
of motor by allowing exposed wiring or solder tabs to cross-connect or ESC applying simultaneous power to
more than one phase at a time from switching to Brush Mode, free-revving motor, or any damage caused by
a crash, flooding, or natural disaster. In no case shall our liability exceed the product’s original cost. We reserve
the right to modify warranty provisions without notice.
Because Novak R/C, Inc. has no control over the connection & use of motor or other related electronics, no liability
may be assumed nor will be accepted for damage resulting from the use of this product. Every motor is thoroughly
tested and cycled before leaving our facility and is, therefore, considered operational. This product is not a toy,
and is not intended for use by children under 14 years of age without the strict supervision of an adult. Use of
this product in a uncontrolled manner may result in physical damage or injuries. Take extra care when operating
any remote control vehicle. By the act of connecting/operating speed control, the user accepts all resulting liability.
e-mail: [email protected]
• (949) 916-6044 • Monday-Thursday
©Novak R/C, Inc. California, U.S.A.
No part of these instructions may be reproduced without the written permission of Novak
R/C, Inc. All Rights Reserved.
ACCESSORIES
MOTOR INSTRUCTIONS
black
orange
white
plastic
tabs
red
blue
green
metal
barbs
raised
metal
barb
metal socket on end of
Teflon sensor harness wires
Should any of the 26G Teflon wires pull out of the motor’s sensor
harness connector, re-insert them in the connector’s appropriate
slot as shown below. There is a small plastic tab that grabs a small
raised barb on the back of the metal socket crimped onto the Teflon
wire’s end. Check the plastic tab to make sure it has not deformed
excessively before inserting the socket into the plastic connector
housing with the barb toward the plastic tabs.
Note: Remove or loosen the bearing cap to remove or insert a sensor harness.
SENSOR HARNESS WIRING
5332
Brushless Motor Wire Set 14GA
--with factory installed bullet connectors
5351 Brushless Shielded Sensor Harness--4”--Double-ended motor sensor harness.
5352 Brushless Shielded Sensor Harness--6”--Double-ended motor sensor harness.
5353 Brushless Shielded Sensor Harness--9”--Double-ended motor sensor harness.
5508
14GA Brushless Wire Set
--2 pieces each of 9” silicone blue, yellow, orange, black & red.
5626 Glitch Buster Capacitor--Stores battery power for receiver to eliminate radio cut-out.
5647 Black Cooling Fan--25x25x10mm--All purpose cooling fan with 2-pin JST connector.
5649 Black Cooling Fan--25x25x10mm--Cooling fan with 2mm Mini plug installed.
5731
3.5mm Power Connectors/5 pair
--Gold plated low-loss connectors for 12-14G wire.
5741
4mm Power Connectors/5 pair
--Gold plated low-loss high-amp 12-14G connectors.
5831 Lead-Free 3% Silver Solder--6g--Low-resistance, high-conductivity solder.
5832 Lead-Free 3% Silver Solder--15g Tube--Low-resistance, high-conductivity solder.
5836 Heavy Duty Lead-Free 3% Silver Solder--25g Tube--Thicker 1.5mm solder.
5850
Heat Shrink Tubing Assortment--6pcs-
-6” pieces in 6 sizes from 1/16-3/8”--Black.
5851
Heat Shrink Tubing Assortment--24pcs
--6” pieces in 6 sizes from 1/16-3/8”--Black.
5852
Heat Shrink Tubing Assortment--40pcs
--1” pieces in 1/4” size--20 each of Red & Black.
5853 Heat Shrink Tubing Box Set--160pcs--4” pieces in 6 sizes from 1/16-3/8”--Black.
5860
Speed Lube--10ml
--Premium American-made bearing oil with penetrative additives
5861
Pro Solder Flux--10ml
--Liquid rosin flux for easy soldering of lead-free solders--Dropper bottle.
SPECIFICATIONS
Input Voltage ................................................................2S LiPo/LiFe cells
Motor Turn .............................................................................. 13.5-turn
Design ......................................................................................Sensored
Motor Size (540) .................................. 02.08” x 1.41” / 52.8 x 35.8mm
Weight ..............................................................................5.8 oz / 164 g
Shaft Diameter .................................................................................1/8”
Rotor ................................... 2-pole, high-strength sintered Neodymium
#55-3074M-1 Rev.1
6-2014
PRECAUTIONS
PRECAUTIONS
NEVER FREE-REV THE MOTOR Free-running your brushless
motor in a no-load condition can result in rotor failure and ESC
transistor damage & will void the product’s warranty!
• WATER & ELECTRONICS DON’T MIX Never allow water, moisture, or
other foreign materials to get inside motor, or on PCBs.
• NOVAK MOTORS & ESCs FOR BEST RESULTS Use Novak sensored
motors with Novak Brushless ESCs for best performance & protection. Only
use motors with the proper number of turns to match ESC’s rating.
• DO NOT USE WITH ESCS THAT HAVE ADVANCE ELECTRONIC
TIMING This can result in excessive heating and motor damage that will
not be covered by the product’s warranty.
• INSULATE EXPOSED WIRES Use heat shrink tubing to prevent shorts.
• NO SOLVENTS Do NOT expose the motor to any type of solvents.
• SET GEAR MESH PROPERLY Too tight of a gear mesh can result in
motor pinion shaft breakage--be sure to adjust mesh properly.
MOTOR MAINTENANCE
• CHECK ALL MOTOR SCREWS for loosening at regular intervals, just like
other hardware on your vehicle. Note: The 3 main socket head screws
that hold the motor together may require tightening after a few runs of
the motor. Also check the 3 flat head screws securing the end cap on
the back of the motor.
• CHECK MOTOR BEARING WEAR after extensive use. The motor’s
closed design will keep most dirt & debris out, but some will get in
and eventually cause wear. If the shaft does not spin freely, you may
need bearing replacement. A small drop of Novak Speed Lube (#5860)
on the bearings periodically can help extend bearing life--however, too
much oil will attract dirt and will cause problems, so apply sparingly.
• CLEAN INSIDE MOTOR periodically by removing front end bell,
removing the rotor, and blowing out the inside of the motor with
compressed air.
Be sure not to lose any small shim washers that may be
on the ends of the rotor shaft & keep them in the correct location.
SERVICE PROCEDURES
After reviewing instructions, tech section and how-to video section of website, if you feel
your motor requires service
(motor may appear to have failed when other problems exist)
, obtain
the most current product service options & pricing by one of the following methods:
WEBSITE:
Print a copy of the product SERVICE FORM from the SERVICE section of the
Novak website. Fill out the needed information & return it with the Novak product.
PHONE/E-MAIL: Contact our customer service department by phone or e-mail, and
we will supply you with current service options.
WARRANTY SERVICE:
You MUST CLAIM WARRANTY on product SERVICE FORM & include
a valid, itemized receipt with the purchase date on it, or an invoice from previous service
work. If warranty provisions have been voided, there will be a service fee.
ADDITIONAL NOTES:
•
Dealers/distributors are not authorized to replace products thought to be defective.
•
If a hobby dealer returns your product for service, submit a completed product SERVICE
FORM to dealer & make sure it’s included with items.
PRODUCT WARRANTY
Novak Brushless motors are guaranteed to be free from defects in materials or workmanship for a period of 120
days from the original date of purchase (verified by dated, itemized sales receipt). Warranty does not cover incor-
rect installation, components worn by use, cross-connection of battery/motor power wires, overheating solder
tabs, damage resulting from thermal overload or operation above 175°F, use of excessive timing or overheating,
splices or damage to the sensor harness, damage from disassembling motor, tampering with internal electronics,
allowing water, moisture, or any other foreign material to enter motor or get onto the PC board, short-circuiting
of motor by allowing exposed wiring or solder tabs to cross-connect or ESC applying simultaneous power to
more than one phase at a time from switching to Brush Mode, free-revving motor, or any damage caused by
a crash, flooding, or natural disaster. In no case shall our liability exceed the product’s original cost. We reserve
the right to modify warranty provisions without notice.
Because Novak R/C, Inc. has no control over the connection & use of motor or other related electronics, no liability
may be assumed nor will be accepted for damage resulting from the use of this product. Every motor is thoroughly
tested and cycled before leaving our facility and is, therefore, considered operational. This product is not a toy,
and is not intended for use by children under 14 years of age without the strict supervision of an adult. Use of
this product in a uncontrolled manner may result in physical damage or injuries. Take extra care when operating
any remote control vehicle. By the act of connecting/operating speed control, the user accepts all resulting liability.
e-mail: [email protected]
• (949) 916-6044 • Monday-Thursday
©Novak R/C, Inc. California, U.S.A.
No part of these instructions may be reproduced without the written permission of Novak
R/C, Inc. All Rights Reserved.
ACCESSORIES
MOTOR INSTRUCTIONS
black
orange
white
plastic
tabs
red
blue
green
metal
barbs
raised
metal
barb
metal socket on end of
Teflon sensor harness wires
Should any of the 26G Teflon wires pull out of the motor’s sensor
harness connector, re-insert them in the connector’s appropriate
slot as shown below. There is a small plastic tab that grabs a small
raised barb on the back of the metal socket crimped onto the Teflon
wire’s end. Check the plastic tab to make sure it has not deformed
excessively before inserting the socket into the plastic connector
housing with the barb toward the plastic tabs.
Note: Remove or loosen the bearing cap to remove or insert a sensor harness.
SENSOR HARNESS WIRING
5332
Brushless Motor Wire Set 14GA
--with factory installed bullet connectors
5351 Brushless Shielded Sensor Harness--4”--Double-ended motor sensor harness.
5352 Brushless Shielded Sensor Harness--6”--Double-ended motor sensor harness.
5353 Brushless Shielded Sensor Harness--9”--Double-ended motor sensor harness.
5508
14GA Brushless Wire Set
--2 pieces each of 9” silicone blue, yellow, orange, black & red.
5626 Glitch Buster Capacitor--Stores battery power for receiver to eliminate radio cut-out.
5647 Black Cooling Fan--25x25x10mm--All purpose cooling fan with 2-pin JST connector.
5649 Black Cooling Fan--25x25x10mm--Cooling fan with 2mm Mini plug installed.
5731
3.5mm Power Connectors/5 pair
--Gold plated low-loss connectors for 12-14G wire.
5741
4mm Power Connectors/5 pair
--Gold plated low-loss high-amp 12-14G connectors.
5831 Lead-Free 3% Silver Solder--6g--Low-resistance, high-conductivity solder.
5832 Lead-Free 3% Silver Solder--15g Tube--Low-resistance, high-conductivity solder.
5836 Heavy Duty Lead-Free 3% Silver Solder--25g Tube--Thicker 1.5mm solder.
5850
Heat Shrink Tubing Assortment--6pcs-
-6” pieces in 6 sizes from 1/16-3/8”--Black.
5851
Heat Shrink Tubing Assortment--24pcs
--6” pieces in 6 sizes from 1/16-3/8”--Black.
5852
Heat Shrink Tubing Assortment--40pcs
--1” pieces in 1/4” size--20 each of Red & Black.
5853 Heat Shrink Tubing Box Set--160pcs--4” pieces in 6 sizes from 1/16-3/8”--Black.
5860
Speed Lube--10ml
--Premium American-made bearing oil with penetrative additives
5861
Pro Solder Flux--10ml
--Liquid rosin flux for easy soldering of lead-free solders--Dropper bottle.
SPECIFICATIONS
Input Voltage ................................................................2S LiPo/LiFe cells
Motor Turn .............................................................................. 13.5-turn
Design ......................................................................................Sensored
Motor Size (540) .................................. 02.08” x 1.41” / 52.8 x 35.8mm
Weight ..............................................................................5.8 oz / 164 g
Shaft Diameter .................................................................................1/8”
Rotor ................................... 2-pole, high-strength sintered Neodymium
1
2
Summary of Contents
Page 1 - MOTOR MAINTENANCE
#55-3074M-1 Rev.16-2014PRECAUTIONSPRECAUTIONSNEVER FREE-REV THE MOTOR Free-running your brushless motor in a no-load condition can result in rotor fai
Page 2 - MOTOR TIMING ADJUSTMENT
MOTOR TIMING ADJUSTMENT1. NO MOTOR CAPACITORS & SCHOTTKY NEEDED Novak brushless motors do not need motor capacitors or external Schottky diodes--
Related products and manuals for For the car Novak Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.273 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals